क्या रास्पबेरी पाई 3 4K वीडियो कर सकती है?


24

ऐसा लगता है कि रास्पबेरी पाई 3 4K वीडियो आउटपुट के लिए पर्याप्त शक्तिशाली हो सकता है, लेकिन मैंने इसके बारे में कहीं भी कुछ भी नहीं देखा है।

क्या किसी को पता है कि 4K रिज़ॉल्यूशन पर Raspberry Pi 3 एचडीएमआई पर वीडियो आउटपुट कर सकता है? यदि हां, तो क्या यह 30 हर्ट्ज या 60 हर्ट्ज है?

जवाबों:


18

सबसे अच्छी जानकारी जो मुझे मिल सकती है वह बताती है कि 4K रिज़ॉल्यूशन को आउटपुट करना संभव है, लेकिन काफी दयनीय फ्रेम दरों पर। Pi 3 में पाई 2 के समान GPU है, इसलिए जानकारी अभी भी मान्य होनी चाहिए:

स्रोत: https://www.raspberrypi.org/forums/viewtopic.php?f=38&t=79330

मैं 1540 पर एक Seiki E50UY04 पर रास्पबेरी पाई पर दो वितरणों के तहत काम करने के लिए 3840 x 2160 (4k x 2k) प्राप्त करने में कामयाब रहा हूं ... (नवीनतम व्हीज़ी / ओपनीलेक)। टेलीविज़न से पता चलता है कि यह इस संकल्प और हर्ट्ज स्तर को प्राप्त कर रहा है, और यह बहुत कुरकुरा लग रहा है।

यह wheezy के लिए मेरा config.txt है:

# uncomment if you get no picture on HDMI for a default "safe" mode
#hdmi_safe=1

# uncomment this if your display has a black border of unused pixels visible
# and your display can output without overscan
disable_overscan=1

# uncomment the following to adjust overscan. Use positive numbers if console
# goes off screen, and negative if there is too much border
overscan_left=-150
overscan_right=-150
#overscan_top=16
#overscan_bottom=16

# uncomment to force a console size. By default it will be display's size minus
# overscan.
#framebuffer_width=3840
#framebuffer_height=2160

# uncomment if hdmi display is not detected and composite is being output
#hdmi_force_hotplug=1

# uncomment to force a specific HDMI mode (this will force VGA)
hdmi_group=2
hdmi_mode=87

# uncomment to force a HDMI mode rather than DVI. This can make audio work in
# DMT (computer monitor) modes
#hdmi_drive=2

# uncomment to increase signal to HDMI, if you have interference, blanking, or
# no display
#config_hdmi_boost=4

# uncomment for composite PAL
#sdtv_mode=2

#uncomment to overclock the arm. 700 MHz is the default.
#arm_freq=800

# for more options see http://elinux.org/RPi_config.txt
hdmi_ignore_edid=0xa5000080
hdmi_cvt 3840 2160 15

यह समान gpu चलाता है लेकिन 250mhz के बजाय 400 पर
इमानुएल सियुरेलो

2
सच। मैंने अभी तक कोई विश्लेषण नहीं देखा है कि 4K फ्रेम दर पर क्या प्रदर्शन प्रभाव पड़ सकता है।
goobering

400 बनाम 250mh एचडीएमआई को स्कैन करने के लिए प्रभावित नहीं करेगा। एचडीएमआई की घड़ियां स्वतंत्र हैं और घड़ी के पेड़ से कहीं और निकलती हैं।
एरिक एनहोल्ट

-3

Chromecast 4k आज़माएं, आप RPI से Chromecast पर स्ट्रीम कर सकते हैं।


यह बहुत पूर्ण उत्तर नहीं है। क्या बैंडविड्थ के उस स्तर को संसाधित / प्रसारित करना आरपीआई केबल है? क्या ऐसा करने के लिए किसी विशेष सेवा की आवश्यकता है?
Jacobm001
हमारी साइट का प्रयोग करके, आप स्वीकार करते हैं कि आपने हमारी Cookie Policy और निजता नीति को पढ़ और समझा लिया है।
Licensed under cc by-sa 3.0 with attribution required.